Application of the Total Productive Maintenance to Increase the Overall Value of Equipment Effectiveness on Ventilator Machines

Main Article Content

Hibarkah Kurnia

Andini Putri Riandani
Tri Aprianto


hospital, Overall effectiveness Equipment, Total Productive Maintenance, Ventilator Machine


A ventilator machine is a medical device that plays an important role in handling Covid-19 cases during a pandemic. Covid 19 patients are arriving at a referral hospital in Jakarta, meaning that the hospital must prepare its medical equipment, including a ventilator machine. The ventilator machine experienced problems because the efficiency of the machine decreased so many patients waited in the ICU room. Machine effectiveness has an average value of 62.26% so it has an impact on disrupting patient services at home. The purpose of this research is to look for factors that cause the lack of effective value of ventilator machines and find effective solutions to increase the effectiveness of ventilator machines so that they can serve Covid-19 patients during a pandemic. This research method combines Focus Group Discussion in determining 5W+1H and implementing the pillars of Total Productive Maintenance to improve the Overall Effectiveness of Equipment on Ventilator machines. This study found a breakdown factor of 54.10%, idle and minor loss of 41.20%, and others of 4.70%. The effect of overall improvement has been able to increase the average effectiveness value by 85.00% from Sep 2021-Feb 2022, so this is supported by the hospital's program in terms of increasing the effectiveness of machines in patient care.


Download data is not yet available.


[1] A. Kumar and L. Murthy, “The PR of China, under its obligations for International Health Regulations,” bioRxiv, vol. 9, no. 4, pp. 1–12, 2020, doi: 10.1101/2020.02.07.937862.
[2] H. Rothan and S. Byrareddy, “The epidemiology and pathogenesis of coronavirus disease (COVID-19) outbreak,” J. Autoimmun., vol. 109, no. 2, pp. 102–116, 2020, doi: 10.1016/j.jaut.2020.102433.
[3] D. M. Maslove, F. Lamontagne, J. C. Marshall, and D. K. Heyland, “A path to precision in the ICU,” Crit. Care, vol. 21, no. 1, pp. 19–21, 2017, doi: 10.1186/s13054-017-1653-x.
[4] X. Yang, Y. Yu, J. Xu, H. Shu, and J. Xia, “Clinical course and outcomes of critically ill patients with SARS-CoV-2 pneumonia in Wuhan, China: a single-centered, retrospective, observational study,” Lancet Respir. Med., vol. 8, no. 5, pp. 475–481, 2020, doi: 10.1016/S2213-2600(20)30079-5.
[5] R. Chang, K. M. Elhusseiny, Y. C. Yeh, and W. Z. Sun, “COVID-19 ICU and mechanical ventilation patient characteristics and outcomes—A systematic review and meta-analysis,” PLoS One, vol. 16, no. 2 February, pp. 1–16, 2021, doi: 10.1371/journal.pone.0246318.
[6] M. Veni, B. S. Sabarguna, and A. Wahyudi, “Analysis of Medical Device Maintenance Management in the Hospital X,” J. Community Health, vol. 6, no. April 2019, pp. 230–236, 2020, doi: 10.25311/keskom.Vol6.Iss2.380.
[7] K. Khlie and A. Abouabdellah, “Identification of the patient requirements using lean six sigma and data mining,” Int. J. Eng. Trans. B Appl., vol. 30, no. 5, pp. 691–699, 2017, doi: 10.5829/idosi.ije.2017.30.05b.09.
[8] D. I. Sukma, H. A. Prabowo, I. Setiawan, H. Kurnia, and I. Maulana, “Implementation of Total Productive Maintenance to Improve Overall Equipment Effectiveness of Linear Accelerator Synergy Platform Cancer Therapy,” Int. J. Eng., vol. 35, no. 07, pp. 1–11, 2022, doi: 10.5829/IJE.2022.35.07A.05.
[9] N. Fajrah and N. Noviardi, “Analisis Performansi Mesin Pre-Turning dengan Metode Overall Equipment Effectiveness pada PT APCB,” J. Optimasi Sist. Ind., vol. 17, no. 2, pp. 126–134, 2018, doi: 10.25077/josi.v17.n2.p126-134.2018.
[10] M. D. Zilberberg and A. F. Shorr, “Ventilator-associated pneumonia: The clinical pulmonary infection score as a surrogate for diagnostics and outcome,” Clin. Infect. Dis., vol. 51, no. SUPPL. 1, pp. 131–135, 2010, doi: 10.1086/653062.
[11] C. Guérin, C. Guérin, P. Lévy, and P. Lévy, “Easier access to mechanical ventilation worldwide: An urgent need for low income countries, especially in face of the growing COVID-19 crisis,” Eur. Respir. J., vol. 55, no. 6, pp. 26–29, 2020, doi: 10.1183/13993003.01271-2020.
[12] M. Mohammadian, M. Babaei, M. A. Jarrahi, and E. Anjomrouz, “Scheduling nurse shifts using goal programming based on nurse preferences: A case study in an emergency department,” Int. J. Eng. Trans. A Basics, vol. 32, no. 7, pp. 954–963, 2019, doi: 10.5829/ije.2019.32.07a.08.
[13] H. Kurnia, C. Jaqin, and H. H. Purba, “The PDCA Approach with OEE Methods for Increasing Productivity in the Garment Industry,” J. Ilm. Tek. Ind. J. Keilmuan Tek. dan Manaj. Ind., vol. 10, no. 1, pp. 57–68, 2022, doi: 10.24912/jitiuntar.v10i1.15430.
[14] S. Subiyanto, “Analisis Efektifitas Mesin/Alat Pabrik Gula Menggunakan Metode Overall Equipments Effectiveness,” J. Tek. Ind., vol. 16, no. 1, pp. 41–50, 2014, doi: 10.9744/jti.16.1.43-52.
[15] H. A. Prabowo, Y. B. Suprapto, and F. Farida, “The Evaluation of Eight Pillars Total Productive Maintenance (TPM) Implementation and Their Impact on Overall Equipment Effectiveness (OEE) and Waste,” Sinergi, vol. 22, no. 1, pp. 13–18, 2018, doi: 10.22441/sinergi.2018.1.003.
[16] C. Jaqin, A. Rozak, and H. H. Purba, “Case Study in Increasing Overall Equipment Effectiveness on Progressive Press Machine Using Plan-do-check-act Cycle,” Int. J. Eng. Trans. B Appl., vol. 33, no. 11, pp. 2245–2251, 2020, doi: 10.5829/ije.2020.33.11b.16.
[17] S. Syarief, “Overall Equipment Effectiveness Measurement,” Proceeding Politeknologi, vol. 14, no. 2, pp. 1–8, 2015.
[18] H. Flaatten and O. Hevrøy, “Errors in the intensive care unit (ICU) experiences with an anonymous registration,” Acta Anaesthesiol. Scand., vol. 43, no. 6, pp. 614–617, 1999, doi: 10.1034/j.1399-6576.1999.430604.x.
[19] J. D. Morales Méndez and R. S. Rodriguez, “Total productive maintenance (TPM) as a tool for improving productivity: a case study of application in the bottleneck of an auto-parts machining line,” Int. J. Adv. Manuf. Technol., vol. 92, no. 1–4, pp. 1013–1026, 2017, doi: 10.1007/s00170-017-0052-4.
[20] I. Pratiwi, “Usulan Penerapan Total Productive Maintenance pada Mesin Turbin Gas,” J. Optimasi Sist. Ind., vol. 18, no. 1, pp. 37–47, 2019, doi: 10.25077/josi.v18.n1.p37-47.2019.
[21] T. Octavia, R. E. Stok, and Y. Amelia, “Implementasi Total Productive Maintenance Di Departemen Non Jahit Pt. Kerta Rajasa Raya,” J. Tek. Ind., vol. 3, no. 1, pp. 18–25, 2001, doi: 10.9744/jti.3.1.pp.%2018-25.
[22] H. Kurnia, C. Jaqin, H. H. Purba, and I. Setiawan, “Implementation of Six Sigma in the DMAIC Approach for Quality Improvement in the Knitting Socks Industry,” tekstilvemuhendis, vol. 28, no. 124, pp. 269–278, 2021, doi: 10.7216/1300759920212812403.
[23] Musyafa’ah and A. Sofiana, “Analisis Penerapan Total Productive Maintenance (TPM) Menggunakan Nilai Overall Equipment Effectiveness (OEE) dan Six Big Losses pada Mesin Disamatik PT. XYZ,” J. Optimasi Sist. Ind., vol. 15, no. 1, pp. 56–63, 2022, doi: 10.31315/opsi.v15i1.6630.
[24] A. Rozak, C. Jaqin, and H. Hasbullah, “Increasing overall equipment effectiveness in an automotive company using DMAIC and FMEA method,” J. Eur. des Syst. Autom., vol. 53, no. 1, pp. 55–60, 2020, doi: 10.18280/jesa.530107.
[25] S. Supriyadi, G. Ramayanti, and R. Afriansyah, “Analisis Total Productive Maintenance Dengan Metode Overall Equipment Effectiveness Dan Fuzzy Failure Mode and Effects Analysis,” Sinergi, vol. 21, no. 3, p. 165, 2017, doi: 10.22441/sinergi.2017.3.002.
[26] H. Kurnia, Setiawan, and M. Hamsal, “Implementation of statistical process control for quality control cycle in the various industry in Indonesia : Literature review,” Oper. Excell. J. Appl. Ind. Eng., vol. 13, no. 2, pp. 194–206, 2021, doi: 10.22441/oe.2021.v13.i2.018.
[27] D. Sjarifudin, H. Kurnia, H. H. Purba, and C. Jaqin, “Implementation of the six sigma approach for increasing the quality of formal men ’ s jackets in the garment industry,” J. Sist. dan Manaj. Ind., vol. 6, no. 1, pp. 33–44, 2022, doi: 10.30656/jsmi.v6i1.4359.
[28] T. Suzuki, TPM In Process Industries. Taylor and Francis Group, 2017. doi: 10.1201/9780203735343.
[29] A. Sutoni, W. Setyawan, and T. Munandar, “Total Productive Maintenance (TPM) Analysis on Lathe Machines using the Overall Equipment Effectiveness Method and Six Big Losses,” J. Phys. Conf. Ser., vol. 1179, no. 1, pp. 1–7, 2019, doi: 10.1088/1742-6596/1179/1/012089.
[30] B. B. Patil, A. S. Badiger, and A. H. Mishrikoti, “A Study on Productivity Improvement through Application of Total Productive Maintenance in Indian Industries-A Literature Review,” IOSR J. Mech. Civ. Eng., vol. 15, no. 3, pp. 13–23, 2018, doi: 10.9790/1684-1503041323.
[31] E. T. Bekar, A. Skoogh, and N. Cetin, “Prediction of Industry 4.0’s Impact on Total Productive Maintenance Using a Real Manufacturing Case,” in Proceedings of the International Symposium for Production Research 2018, 2019, pp. 136–149. doi: 10.1007/978-3-319-92267-6.