Peningkatan Mutu Proses Pembuatan Cat Solvent dengan Metode Taguchi di PT JI
Main Article Content
Keywords
Kualitas, Right First Time (RFT), Taguchi, Kapabilitas Proses, ANOVA
Abstract
In a manufacturing process, quality is not only seen from the final product, but also manufacturing process. PT JI located in Cikarang is a company that produces paints and powder coating. Currently, the company has problems with 24.16% products that need rework or additional process. To increase productivity, PT JI applies the A3 project that is Right First Time (RFT). RFT is how to create a product with a one-time process and produce a product that has good quality on the first test. The average percentage of total RFT products in September 2016-January 2017 was 75.84%. This result is still below the company target of 80%. This study found the source of problems analyzed the manufacturing process using control chart, process capability, fishbone, and pareto. Taguchi method and ANOVA are applied to improve the design process. The application of the Taguchi Method shows that the factors which influence the value of viscosity quality are number of White Spirit, Number of Genekyd, Total Tio2 (kaolin), and mixing temperature, where each factor has an optimal level of 26.01%, 56.07%, 18.78% and 45oC. Then, it is found that all control factors have significant effect on viscosity value from ANOVA analysis. The application of this Taguchi method increases the process capability to Cp = 1.68 and Cpk = 1.43 from Cp = 0.29 and Cpk = 0.18, as well as an increase in RFT percentage of 5.78% or to 81.62% over the last two months.
References
[2] A. V. Feigenbaum, Total Quality Control, Third Edit. Singapore: Mc Graw Hill Book, 1991.
[3] D. C. Montgomery, Introduction to Statistical Control Quality Control, 5th Editio. Hoboken NJ: Wiley, 2004.
[4] S. Assauri, Manajemen Operasi dan Produksi, Edisi keti. Jakarta: PT Raja Grafindo Persada, 2016.
[5] J. M. Juran, Juran on leadership for quality. New York: Simon and Schuster, 2003.
[6] S. Muis, Metodologi Six Sigma Teori dan Aplikasi di Lingkungan Pabrikasi. Yogyakarta: Graha Ilmu, 2014.
[7] S. Taguchi, Genichi, Chowdhury and W. Yuin, Taguchi’s Quality Engineering Handbook. New Jersey: John Wiley & Sons, Inc., 2005.
[8] R. Rakasita, B. W. Karuniawan, and A. I. Juniani, “Optimasi Parameter Mesin Laser Cutting Terhadap Kekasaran Dan Laju Pemotongan Pada Sus 316l Menggunakan Taguchi Grey Relational Analysis Method,” J@TI UNDIP J. Tek. Ind., vol. 11, no. 2, pp. 97–106, 2016. https://doi.org/10.14710/jati.11.2.97-106
[9] A. Anantama, N. B. Puspitasari, and A. Arvianto, “Menentukan Kombinasi Optimal Parameter Coffee Roasting Untuk Mendapatkan Roasted Bean Dengan Tingkat Kematangan Medium Roast Menggunakan Metode Taguchi,” J@TI UNDIP J. Tek. Ind., vol. 10, no. 3, pp. 163–168, 2015.
[10] N. Irawati, N. T. Putri, and A. H. B. Adi, “Strategi Perencanaan Jumlah Material Tambahan dalam Memproduksi Semen dengan Pendekatan Taguchi untuk Meminimalkan Biaya Produksi (Study Kasus PT Semen Padang),” J. Optimasi Sist. Ind., vol. 14, no. 1, pp. 176–191, 2016. https://doi.org/10.25077/josi.v14.n1.p176-191.2015
[11] M. S. Effendi, A. M.K., and A. Hendrawan, “Peningkatan Kekuatan Puntir Produk Baling-Baling Kapal Bahankuningan Dengan Pendekatan Metode Taguchi Pada Industri Kecil Pengecoran Negara Kandangan Kalimantan Selatan,” J. Spektrum Ind., vol. 12, no. 1, pp. 29–41, 2014. https://doi.org/10.12928/si.v12i1.1647
[12] M. Hartono, “Meningkatkan mutu produk plastik dengan metode taguchi,” J. Tek. Ind., vol. 13, no. 1, pp. 93–100, 2012. https://doi.org/10.22219/JTIUMM.Vol13.No1.93-100
[13] R. Purwaningsih, N. Utami, and H. Kuncara, “Penentuan Parameter Permesinan Terbaik Untuk Meminimasi Penyimpangan Geometri Kesilindrisan Baut Segienam J-01 Dengan Metode Taguchi,” J@TI UNDIP J. Tek. Ind., vol. 1, no. 1, pp. 1–9, 2006.
[14] J. Julianingsih, D. A. Y. Aysia, and D. Soegianto, “Penentuan Komposisi Bahan Baku Optimal Produk Kecap X Dengan Metode Taguchi,” J. Tek. Ind., vol. 6, no. 2, pp. 121–133, 2005.
[15] J. Julianingsih and F. Prasetyo, “Penentuan Kondisi Pengolahan dan Penyajian Bumbu Rawon Instan Bubuk Dengan Metode Taguchi,” J. Tek. Ind., vol. 5, no. 2, pp. 90–100, 2004.
Article Sidebar
Article Details
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Authors' Retention of Copyright
Authors retain the copyright of their original work published in Jurnal Optimasi Sistem Industri (JOSI). By submitting their manuscript to the journal, authors grant Jurnal Optimasi Sistem Industri (JOSI) a non-exclusive license to publish the work under the CC BY-NC-SA 4.0 International License. This means that others are permitted to:
- Share and adapt the work for non-commercial purposes, provided proper attribution is given to the original authors and source.
- Create derivative works based on the original article, as long as the new work is non-commercial and under the same CC BY-NC-SA 4.0 International License.
Non-Commercial Usage
The CC BY-NC-SA 4.0 International License restricts commercial use of the published work and its derivatives. Commercial use includes generating revenue, financial gain, or any form of commercial exploitation. This limitation aims to preserve the scholarly and educational nature of the content.
ShareAlike Requirement
If you remix, adapt, or build upon the work, you must distribute your contributions under the same CC BY-NC-SA 4.0 International License as the original work. This "ShareAlike" requirement ensures that any new works based on the original content adhere to the same non-commercial, share-alike principles.
Usage, Attribution, and Citations
Authors and readers are allowed to:
- Share and distribute the published article in any medium or format.
- Adapt, remix, transform, and build upon the article for non-commercial purposes.
- Provide appropriate attribution to the original authors and the journal.
When using content from Jurnal Optimasi Sistem Industri (JOSI), proper attribution must be provided through citation of the original source and authors.
Copyright Infringement and Ethical Considerations
If you believe that any material published in Jurnal Optimasi Sistem Industri (JOSI) infringes upon your copyright or the copyright of someone you represent, please contact the editorial team promptly. The journal is committed to addressing copyright concerns in accordance with established ethical guidelines set forth by the Committee on Publication Ethics (COPE).
For any questions or inquiries related to copyright and licensing, please contact the editorial team at editor_josi[at]eng.unand.ac.id.